Tds foresight reverse northing easting
>Are your rods or tribrachs in adjustment? There was one area that I had to sight through a chainlink fence.very narrow passage. > Did you have any suspect occupations that raised any concerns?
#Tds foresight reverse northing easting pro
If I recall you use Survey Pro with Ranger 500 right? Do you upload TDS Raw data? I have Carlson.where do you find this routine. Oh, the "DV" line is for just a distance measurement, such as the distance to the backsight. If you have repeat measurements that you want to enter as separate quantities, enter multiple measurements. M From-At-To HorizAngle HorDist DeltaHgt HI/HT # for HDist HgtDiff entry M From-At-To HorizAngle SlopeDist ZenAngle HI/HT # for SDist ZAng entry To specify the coordinates (and height of some station upon which the traverse begins) thusly:Ĭ PtNo Northing Easting Height ! ! ! # the exclamation marks indicate a value that is to be held fixed in the adjustment If you can post your traverse in Star*Net format, I'll bet more than a few posters will have something to offer toward debugging it. The way that I'd approach the problem is to run the traverse through Star*Net to begin with, to see if particular stations look suspicious enough to merit remeasurements. Would anyone will be willing to share the step by step procedure you would apply the error detection procedure? What is the next step to find blunders and outliers to correct the errors? Is that possible for this much error? In those instances I turned 16 sets of angles-with couple pushes of button of course ? There are several places I had to traverse from a short leg to and longer traverse legs. > I took a lot care within my limited knowledge and skill as novice.
#Tds foresight reverse northing easting series
What type of prisms are you using for your traversing? I seem to remember that you are using a Trimble 5600 series robot. Sometimes steep vertical angles can mess up your shots as well. I try to keep them as balanced as possible. If that re-observation does not bring the traverse into closure, then we'll re-run it.ĭid you have any suspect occupations that raised any concerns? Are your rods or tribrachs in adjustment?īalanced shots (backsights and foresights) are desirable, but not always possible. Our first task will be to re-observe the suspect occupation. The weather has not been favorable, so we have not returned to the field to check it yet, but we are scheduled to head back out there Tuesday. I used Carlson's find bad angle routine, and sure enough, the angle it reported, was one that I remembered looking at a shadowy backsight and into a glaring (sunny) foresight. I ran a traverse a week or two ago, and it had an unacceptable mis-closure. Unfortunately, it happens to all of us sometimes.
![tds foresight reverse northing easting tds foresight reverse northing easting](https://manualmachine.com/html/49/4934/49340bdfbc97691d56857b8adddc068263b34af1c93ec14ad92229c8a75ad3f6/htmlconvd-pIrvow23x1.jpg)
Does this look pretty bad that I should start over again? Would anyone will be willing to share the step by step procedure you would apply the error detection procedure?ģ. What is the next step to find blunders and outliers to correct the errors? Is that possible for this much error?Ģ. In those instances I turned 16 sets of angles-with couple pushes of button of course ?ġ. I took a lot care within my limited knowledge and skill as novice. Northing:-0.51 Feet Easting:0.67 Feet Elevation:0.36 Feet
![tds foresight reverse northing easting tds foresight reverse northing easting](https://courses.washington.edu/fe451/handbook/TDS_WORKS_files/image004.jpg)
When I closed the loop…and to my disappointment I got the following result ?
![tds foresight reverse northing easting tds foresight reverse northing easting](https://img.yumpu.com/42907793/1/500x640/tds-cogo48-cogo-card-users-manual-equal-parenting-bc.jpg)
Total horizontal distance of the loop was 9315.38FT. Satisfied with my progress, I embarked on the larger loop within a 70 acre parcel(s). I did pretty well with my smaller six points loop with a very tight closure. I worked on the closed loop traverse with the intention of creating control network.